Save time and money on water main replacements with the latest trenchless techniques from EPS.
Select your installation type and pinpoint your exact start and end locations on our interactive map to get started!
We replace and install water mains pipes for homes and businesses all over the UK by using impact moling technology.
New pipes are installed underneath lawns, paths and driveways without the need to disturb them by digging messy trenches.
We have been using impact moling to install waterpipes and utilities underground since 2011 from our base near Kettering in Northamptonshire. Call us on 0800 622 6024 or send a couple of photos through the form and we explain how we can carry out a new installation for you and what it will cost.
Nearly every call we get is one of three things. A leak on the water pipe between the stop tap at the boundary of the house. This is usually spotted as due to a wet patch on the lawn, or a letter from the water company about high usage. Low pressure is often caused by an old lead or galvanised pipe that has furred up. Or it may be due to a lead pipe that needs replacing. However, the fix is the same for all three issues.
New 25mm or 32mm blue MDPE pipe which is moled in from the stop tap to the house. Most domestic replacements cost between £850 and £1,900. This is a fixed price, and the installation is usually completed in one day, subject to distance and ground conditions.
A mole is a steel cylinder driven by pulsed compressed air. It hammers its way through the ground, pushing the soil outwards and packing it rather than digging it out, so there is no spoil to cart away.
The job starts with the pits. Before we dig anything we trace and mark the customer’s other services (gas, electric, drains, telecoms) so we know exactly what is in the ground. Then we dig the pits 10 to 12 metres apart, each about 1 metre long, 0.6 metres wide and 1 metre deep on average. A short run from the stop tap to the house needs two. The mole is lined up in the launch pit for direction and depth. Once it is running it cannot be steered, so it travels in a straight line to the next pit. If it is a longer run, additional pits are required, typically 10 to 12 metres apart.
Once the mole has come through into the exit pit, we take it off the air hose. The hose is still lying in the bore. We fix the new water pipe to the end of it with a tapered fitting we call a carrot, then go back to the launch pit and pull the hose back through. The pipe follows it.
Moling works best in compressible ground: clay, silt and peat. We work in 10 to 12 metre shots between pits, and moling rates are generally up to 30 metres a day in good ground conditions. It is less suited to sand and gravel, especially where it is densely packed, and it will not go through solid rock. On larger distances we use our horizontal directional drilling rigs instead. Those steer, so one bore can run under a road, a river or a long drive without a pit every 10 to 12 metres.
For a house supply we are putting in 25mm or 32mm pipe, and on domestic work we use a 55mm HammerHead mole. A smaller mole means smaller pits, which keeps the time and the cost down. We mole pipe up to 63mm. Anything bigger than that goes in with our HDD rigs. The patio, the block paving and the tarmac stay exactly where they were, which is the whole point.
1.
You ring or fill in the form. We ask for the distance from the stop tap to the house, what is in between (lawn, block paving, tarmac, concrete) and what the problem is. Photos help. A WhatsApp video of the garden helps more. If it is easier, we will do a quick FaceTime or WhatsApp video call and you can walk us round it.
2.
We quote. It is a fixed price for the job. Most domestic replacements come in between £850 and £1,900.
3.
On the day we trace and mark your other services first, then dig the pits 10 to 12 metres apart along the run and mole between them. We pull the new pipe through on the carrot, connect at each end, flush and test, and reinstate every pit. Most replacements are done in a day, subject to distance and ground conditions.
4.
The work is signed off by our WaterSafe approved staff and you get the paperwork.
The water company owns the main in the road and the pipe up to the stop tap at your boundary. From the stop tap to your kitchen is yours, and so is the bill for fixing it. If the leak is on their side, ring them, not us. Not sure which side it is? Send us a photo of the stop tap and where the wet patch is. We will tell you for what’s best moving forward.
If your house was built before 1970 there is a fair chance the supply pipe is lead. We replace them. Most water companies run a lead pipe replacement scheme for their side of the stop tap, and we can tell you whether yours does. There is more on our lead water pipes page.
The whole of the UK. Our own crews work out of Hannington near Kettering, and we have approved contractors across the UK. Every job is signed off by our WaterSafe approved staff, and either way you deal with EPS from quote to sign-off. Pages for Leicester, Leicestershire, Worthing, Melton Mowbray and Oxfordshire are here if you want the local detail.
EPS Watermains is a trading name of EPS Trenchless Installations Ltd, company number 07739433.
Three photos: the stop tap, the house, and whatever is in between. Or send us a WhatsApp video walking from one to the other, which is better still. If you would rather show us live, we do FaceTime and WhatsApp video calls. Then we will tell you whether moling will do it, what it will cost and when we can come. 0800 622 6024, or the quote form.
Most domestic replacements come in between £850 and £1,900. Where yours lands depends on distance and ground conditions. We quote a fixed price after seeing photos, a video or the site, and that is what you pay.
Most replacements are done in a day, subject to distance and ground conditions. Your water is off for an hour at most while we connect, flush and test. If the leak is bad we may turn it off while we do the replacement, and we will tell you if that is the case.
Replace it, nearly always. By the time a supply pipe has sprung a leak it is coming to the end of its life, and a repair now usually means another call-out later. Replacing it is better value and you get a new pipe with no weak spots.
No. We dig small pits 10 to 12 metres apart along the run, each about 1 metre long, 0.6 metres wide and 1 metre deep on average. On a typical front garden that is one at the stop tap and one at the house, and the mole does everything in between. The pits are reinstated when we are done.
The water company owns the pipe up to the stop tap at your boundary. From the stop tap to the house is yours. That is the bit we replace.
Blue MDPE, usually 25mm or 32mm for a house. It does not corrode, does not fur up and does not contain lead. We mole pipe up to 63mm; anything bigger goes in with our HDD rigs.
Turn every tap off, flush nothing, and go and look at the meter. Still moving? You are losing water between the meter and the house. A soft patch on the lawn on the house side of the stop tap nearly always means the supply pipe. So does a letter from the water company about a jump in usage. If in doubt, send us a photo of the stop tap and we will tell you. If it is not obvious where the leak is, we do leak detection and pipe tracing as well.
Yes. A new MDPE pipe moled in from the boundary replaces the lead on your side. Most water companies run a lead pipe replacement scheme for their side, and we can tell you whether yours does. More on our lead water pipes page.
Usually not when the work is done by a WaterSafe approved contractor. WaterSafe approval means we certify our own work under the water fittings regulations, so you do not have to notify the water company yourself. You get the certificate and the paperwork.
If the cause is an old narrow or furred-up supply pipe, yes. If the pressure is low at the main itself, a new pipe will not change that, and we will tell you so before you spend anything.
Yes. Moling goes underneath. We need a pit at each end of every shot. Shared supplies that serve more than one house are a separate job and we can quote for separating a shared supply.
We do not come through the floor. The new pipe comes up the outside wall inside an insulated housing called an Insuduct, made by Groundbreaker. It protects the pipe from frost on the outside of the building and takes up to two 32mm pipes. No digging inside, no cabinets out, no floors up.
No. On every job we trace and locate the customer’s other services before we dig: gas, electric, drains, telecoms, anything else in the ground. We mark them out before we dig. We do pipe tracing and leak detection as a service in its own right.
Small pits every 10 to 12 metres along the run, so two on most front gardens. On average each pit is about 1 metre long, 0.6 metres wide and 1 metre deep. Reinstating the pits is included in the price. The exceptions are resin-bound surfaces and pressed concrete, which can need a specialist to make good. If you have either, tell us when you get in touch and we will advise.
A leak on your side keeps running and if you are on a meter you pay for the water. A lead pipe keeps putting lead into your drinking water. Neither gets better on its own.
Yes. In England and Wales supply pipe work has to comply with the Water Supply (Water Fittings) Regulations 1999, and in Scotland with the Water Byelaws. Our work is signed off by our WaterSafe approved staff and you get the paperwork.
The whole of the UK. Our own crews work out of Hannington near Kettering, and we have approved contractors across the country for jobs further afield. Either way you deal with EPS from quote to sign-off.
Often not. We can price most domestic jobs from photos or a WhatsApp video of the run from the stop tap to the house. If you would rather talk it through, we will do a FaceTime or WhatsApp video call and you can walk us round.
WaterSafe approved, Which? Trusted Trader, TrustATrader verified with over 250 reviews, Constructionline Gold, SafeContractor, Street Works qualified. Trading since 2011 as EPS Trenchless Installations Ltd, company number 07739433.
EPS Watermains is a trading name of EPS Trenchless Installations Ltd, company number 07739433.